Bona Spray Mop Not Spraying? 7 Fixes
Disclosure: FloorsMop is reader-supported. As an Amazon Associate, we earn from qualifying purchases. If you buy through a link on this page, we may earn a small commission at no extra cost to you. Learn more.
Quick answer: A Bona spray mop that won’t spray usually has a cartridge that isn’t fully seated, a cap that is loose, or a clogged nozzle. Take the cartridge out, check the cap, and push it back in firmly. Then soak the nozzle in warm water and squeeze the trigger 10 to 20 times over a towel to prime it. If the trigger feels loose, the trigger cable may have slipped.
Bona spray mops have no batteries or pump. The trigger on the handle works a simple mechanism that opens a valve and lets cleaner flow to the nozzle. That makes them easy to fix at home. For problems that apply to every brand, see why spray mops stop spraying.
Quick Fix Checklist (Try These First)
| Symptom | Likely cause | Fix | Time |
|---|---|---|---|
| Trigger works, nothing comes out | Cartridge not seated or empty | Reseat or refill the cartridge | 1 min |
| Only a dribble | Partly clogged nozzle | Soak and clear the nozzle | 10 min |
| Trigger feels loose or floppy | Trigger cable slipped | Check the handle connection | 5 min |
| Sprays, then stops | Air in the line or vacuum in the cartridge | Prime; loosen the cap slightly | 2 min |
| Leaks near the mop head | Loose fitting or cracked cartridge | Reseat; try another cartridge | 2 min |
| Spray goes sideways | Dirt on the nozzle tip | Wipe and clear the tip | 2 min |

7 Reasons Your Bona Spray Mop Isn’t Spraying
1. The cartridge is not seated
The cartridge has to sit fully in its holder so its valve meets the spray mechanism. A cartridge that is slightly out will not feed cleaner, even when the trigger moves.
Fix: Remove the cartridge, check the cap and the holder for dried cleaner, then push it back in until it locks. On most models you will feel it snap into place.
2. The cartridge is empty or the cap is wrong
Cartridges are opaque on some versions, so it can be hard to tell how full they are. If you use a refillable cartridge, the cap and valve also need to be put back on correctly after refilling.
Fix: Shake the cartridge to check the level. If you refill, make sure the cap is screwed on straight and snug, not cross-threaded. Try a fresh cartridge to rule out a faulty valve.
3. The nozzle is clogged
Dried cleaner, dust and hard-water minerals block the tiny nozzle opening. This is the most common cause of weak or uneven spray on mops that are a few months old.
Fix:
- Remove the cartridge.
- Soak the nozzle end of the mop head in a shallow dish of warm water for 10 minutes, or hold a warm, damp cloth over it.
- Clear the opening gently with a pin.
- Reinstall the cartridge and test over a towel.
4. The trigger mechanism has slipped
When you squeeze the trigger, a cable or rod inside the handle moves the valve. If a handle section is not fully screwed together, or the mechanism has slipped, the trigger moves but nothing opens.
Fix: Unscrew and reconnect each handle section firmly. Squeeze the trigger and watch the valve area near the cartridge. If nothing moves, the mechanism is broken. Owners report that this is the most common permanent failure on spray mops with a mechanical trigger.
5. Air or a vacuum is blocking flow
Cleaner can’t leave the cartridge if air can’t get in to replace it. On sealed cartridges, this can make the spray slow down and stop.
Fix: Prime the system by squeezing the trigger several times over a towel. If spray starts and stops, loosen the cap a quarter turn to let air in, test, then tighten it again.
6. The wrong cleaner is in the cartridge
Bona mops are made for Bona’s thin, water-based cleaners. Oil soaps, dish soap and thick homemade mixes can leave a film inside the nozzle and slow the flow.
Fix: Empty the cartridge, rinse it with warm water, run warm water through the nozzle, and refill with a Bona cleaner made for your floor. See how to use a Bona mop for the right cleaner for each floor type.
7. A part is cracked
A cracked cartridge, holder or nozzle can leak instead of spraying. Look for drips on the floor where you store the mop.
Fix: Replace the cracked part. Cartridges and pads are sold separately, but a cracked holder usually means replacing the whole mop.
Notes by Model
| Model | What to know |
|---|---|
| Bona Premium Spray Mop | Uses a cartridge in a holder near the head. Seating and nozzle clogs are the main issues. |
| Bona Hardwood Floor Spray Mop | Same idea with a hardwood cleaner cartridge. Use only hardwood-safe cleaner. |
| Bona Hard-Surface Spray Mop | For tile, vinyl, stone and laminate. Don’t use the hardwood cleaner on stone. |
| Refillable cartridge versions | Check the cap is straight after every refill. |
Our Bona cartridge review covers the cartridges in more detail.
Keep It From Happening Again
- Use only thin, residue-free floor cleaner.
- Rinse the nozzle with warm water once a month.
- Store the mop upright so the nozzle stays clean.
- Wash pads without fabric softener.
- Don’t leave an almost-empty cartridge in the mop for months.

Warranty, Support and Replacement
Contact Bona customer service if a new mop never sprayed properly or the trigger failed soon after you bought it. Keep your receipt. If the mop is old and the trigger mechanism is broken, a new mop costs little more than a new set of pads and cartridges.
Thinking of switching? Compare options in our guide to the best spray mops for hardwood floors.
Replacement Parts and Alternatives
- Cleaner: Bona Hardwood Floor Cleaner refill cartridges or Bona Hard-Surface refill for other floors.
- Pads: washable Bona microfiber cleaning pads keep the spray spreading evenly.
- Alternative mop: the O-Cedar ProMist MAX has a refillable bottle you can see into.
If you have a Shark steam mop that also stopped working, our guide on why a Shark steam mop is not steaming may help. For more on Bona products, read how to use Bona floor cleaner with a regular mop, and for technique, see how to mop a floor properly.
FAQs
Why is my Bona mop not spraying after refilling?
The cap may be cross-threaded or loose, or there may be air in the line. Re-cap it straight and squeeze the trigger several times over a towel to prime it.
How do I unclog a Bona spray mop nozzle?
Remove the cartridge, soak the nozzle end in warm water for about 10 minutes, then gently clear the opening with a pin.
Can I put homemade cleaner in a Bona spray mop?
Bona recommends its own cleaners. Thin solutions are less likely to clog, but soaps and oils leave film in the nozzle. See what liquid to put in a spray mop.
Why does my Bona trigger feel loose?
A loose trigger usually means a handle section is not screwed tight or the mechanism inside has slipped. Tighten every section and test again.
Does a Bona spray mop use batteries?
No. Bona spray mops use a manual trigger. If there is no spray, the problem is mechanical, not electrical.
